Attention, Internet Explorer User Announcement: Jive has discontinued support for Internet Explorer 7 and below. In order to provide the best platform for continued innovation, Jive no longer supports Internet Explorer 7. Jive will not function with this version of Internet Explorer. Please consider upgrading to Internet Explorer 8, 9, or 10, or trying another browser such as Firefox, Safari, or Google Chrome. (Please remember to honor your company's IT policies before installing new software!) • • • •. Delphi ds150e software download. Download Cisco IOS image for GNS 3. Hi dear all, that’s really a great to share my hard work with you, After a lots of hit in Google I finally So without talking much here are the link where you can free download Cisco ios image and you can upload or use this ios to the router and as well as in GNS 3. The old ISCW course had a large section on ipsec vpns, not sure where it sits in the new courses though. Remeber with gns3/dynamips etc. You'll still need an IOS image to load on, for VPNs you'll need one with 'k9' in the name. You'll also need two virtual routers to really get to grips with it. For some quick info though you'll need something along these lines: en conf t crypto isakmp policy 1 group 2 hash md5 authentication pre-share encryption 3des crypto isakmp key Trivious_Secret_Key address b.b.b.b no-xauth crypto map Trivious_Map 1 ipsec-isakmp set peer b.b.b.b set transform-set 1 match address Protect_Me ip access-list extended Protect_Me permit ip x.x.x.x 0.0.0.255 y.y.y.y 0.0.0.255 Where x.x.x.x is your local lan subnet and y.y.y.y is the remote lan subnet. If you have more than one subnet on either end of the link just add the necessary lines to the access list. B.b.b.b is the remote router's public ip address. You'll need to repeat (but reverse) the above on the other router. In a lab/virtual environment you'll probably use ethernet connections between the routers, in the real world it's likely you'll be using pppoa/pppoe WAN interfaces with NAT. In this case you must make sure your NAT source list denies the same subnets as your VPN access list, otherwise the traffic will pass through the NAT first and never hit the VPN config. Cisco have some good examples on their website, otherwise get yourself some ccnp books and have a go through them. Good luck with the interview. The old ISCW course had a large section on ipsec vpns, not sure where it sits in the new courses though. Remeber with gns3/dynamips etc. You'll still need an IOS image to load on, for VPNs you'll need one with 'k9' in the name. You'll also need two virtual routers to really get to grips with it. For some quick info though you'll need something along these lines: en conf t crypto isakmp policy 1 group 2 hash md5 authentication pre-share encryption 3des crypto isakmp key Trivious_Secret_Key address b.b.b.b no-xauth crypto map Trivious_Map 1 ipsec-isakmp set peer b.b.b.b set transform-set 1 match address Protect_Me ip access-list extended Protect_Me permit ip x.x.x.x 0.0.0.255 y.y.y.y 0.0.0.255 Where x.x.x.x is your local lan subnet and y.y.y.y is the remote lan subnet. Pelajaran sbk kelas 5 semester 1. If you have more than one subnet on either end of the link just add the necessary lines to the access list. School management software with source code in php. B.b.b.b is the remote router's public ip address. You'll need to repeat (but reverse) the above on the other router. In a lab/virtual environment you'll probably use ethernet connections between the routers, in the real world it's likely you'll be using pppoa/pppoe WAN interfaces with NAT.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |